Reset your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may need to restore your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the configurations or are experiencing unexpected performance. Fortunately, resetting your Holosun is a straightforward process that can be completed in just a few actions.

• First ensuring your red dot sight is turned on.
• Identify the small reinitialize button on the rear of the device.
• Use a small object to press and hold the reset switch for approximately 7 milliseconds.
• Let go the lever and your Holosun EPS Carry Red Dot sight will power cycle.
• Its red dot sight should now be reverted to its factory settings.

Reset Your Holosun EPS Carry Red Dot toward Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it to default configuration is a breeze. First, locate the tiny button on the side of your optic. Then, press and hold it for around ten seconds until you see the red dot blink. Your Holosun EPS Carry is now returned to its factory settings, ready for consistent targeting.

restore Your Holosun EPS Carry Back to Life

Is your beloved Holosun EPS Carry experiencing some performance problems? Don't despair! A simple factory reset can often resolve the problem and get your red dot sight back to its former glory. Before you begin, remember to detach the battery from your Holosun EPS Carry to prevent unintended activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these straightforward steps:

• Simultaneously press and hold the power button for approximately 10 seconds.
• A message will flash, indicating that the reset is being performed.
• Stop pressing the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can re-attach the battery and verify your sight's functionality. If you encounter any further troubles, don't hesitate to contactsupport team.

Revert Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Accomplish these steps carefully to ensure a successful factory reset.

• First, Energize your Holosun EPS Carry by pressing the power button.
• After that, press and hold both the mode button and the up/down adjustment button simultaneously.
• During continue holding these buttons, activate the power button once.
• A message will show a confirmation prompt indicating that the reset process is initiated.
• Allow the process to conclude. This may take a few moments. Once done, your Holosun EPS Carry will automatically power off.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Reset All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Holding a specific button combination. Consult your Guidebook for the exact button sequence for your model. Once in the settings menu, look for an option that says "Clear Settings". Select this option and confirm the reset. Your sight will then power off and restart with all settings Returned to their default values.

Reset your Holosun EPS Carry with a Factory Default Settings

If your Holosun EPS Carry is acting up, a factory reset might be the fix. This will restore your sight to its original settings, clearing any custom configurations you've made. To accomplish this reset, adhere to read more these simple steps:

• First, identify the reset button on your EPS Carry.
• Secondly, engage a small object, like a paperclip, to activate the reset lever.
• During maintain the reset lever pressed, activate your EPS Carry.
• The sight will flash a message indicating that the reset is complete.

Once the reset is complete, your EPS Carry will be back to its factory settings.

Report this wiki page